Frete Grátis em todos os produtos
- It is used for automatic line regulation, safety protection, conversion circuit, etc. It is suitable for various places such as workshops, factories, high-rises, and houses.
- Coil voltage: DC12V，Coil Power: DC (W) ≤0.9,AC (VA): ≤1.2
- Contact Structure: 8 pins 2 normally open 2 normally closed，Contact capacity: 10A 250VAC
- Pull-in voltage: ≤80% (V)，Release voltage: DC: ≥10% (V), AC: ≥30%
- Contact resistance: ≤50 (mΩ)，Insulation resistance: ≤100 (mΩ)
7N0951253#507 12VDC 50A 5 Pins Automotive Replacement Electrical System Relay Starter Relay Fits for 3D0951253A 95561502700
*$325.00
Aeola OEM GM 2 Pack 13500114/8385 High Power 4 Pin Fuse Box Relay 12VDC for Fan air Conditioner Relay
*$289.00
Frete Grátis em todo o BrasilProduto Original Importado dos EUA
Ximimark 5Sets DC 12V Coil Power Relay LY2NJ HH62P JQX-13F DPDT 8 Pin 10A With Socket Base
*$313.00
Informação adicional
| Connector Type | Socket |
|---|---|
| Contact Type | Normally Open |
| Current Rating | 10 Amps |
| Mounting Type | Socket Mount |
| Brand | Ximimark |
| Operation Mode | Automatic |
| Coil Voltage | 12 Volts |
| Contact Current Rating | 10 Amps |
| Maximum Switching Current | 10 Amps |
| UPC | 657835635039 |
| Package Dimensions | 7.05 x 5.04 x 1.34 inches |
| Item Weight | 10.2 ounces |
| Manufacturer | Ximimark |
| Item model number | LY195 |
| Is Discontinued By Manufacturer | No |
| Date First Available | November 30, 2018 |
![True MODS 6 Pack 4-Pin 12V Bosch Style Fused Relay Switch Kit [Interlocking Harness Socket Holder] [14 AWG Hot Wires] [SPST] [30 Amp] 12 Volt Automotive relays with Fuse for...](https://m.media-amazon.com/images/I/81FVp-H-BUL._SL1500_.jpg)
Zach&Heather –
Functional and work as expected.
Mark Grass –
This relays and sockets arrived quickly and they were priced well. THey work great too. Pull in voltage is 7.5v; drop out voltage is about 3v.
Eric Baker –
Relays work well, but are a bit loose on a DIN rail, thus 4 stars.
At 12 Volts, the coils draw 72 milliamps. Polarity is important if you want the LED to work.
Tyer –
I’m using these dpdt relays to reverse the polarity on a gate actuator for the open and close functions.
YBYMOT –
Quality product lasts for years, I’m a journeyman electrician, so I appreciate good products !!! Thank you Amazon 🙂
Tyer –
I’ve purchased these relays a couple of times (5-packs), and in general I find them to be adequate general-purpose signal relays. My control systems usually use 12 volt power, and these allow me to control the occasional 120-volt circuit, or other applications as general interposing relays. Usually, they work fine and have been reliable. As others have noted, the screw terminals are on the small side, but I’ve been migrating to 18-AWG and smaller control wiring anyway, so it hasn’t been much of an issue.
However, I was using one to control a heater, which draws pretty close to the rated current of the relay. It’s a 1000-watt heater, which calculates out to 8.3 amps at 120 volts, and the actual measured current was a bit less than that at 8.15 amps; the relay contacts are rated for 10 amps at 120 volts. It worked fine for a while, perhaps 100 hours and 20-30 cycles, but eventually the relay housing and base melted, and the contacts welded (relay stuck on).
As you can see in the picture, most of the melting occurred at the base-to-relay interface, indicating perhaps a high contact resistance, but that doesn’t explain the contacts welding. The relay plugs in quite firmly, so I wouldn’t have expected a bad contact there, and 10 amps or less isn’t really that much current, so it may have been heat propagating down the internal structure from the contacts. Either way, it didn’t meet its rated current specification very well…
I’ll probably continue to use these, because they are a good value, but I’ll de-rate them to 5 amps and use another model for any future higher-current loads.
Christopher W. –
Great price for 10, no troubles so far
W. B. Sage –
They are as described. The LED lights when the relay is active/closed. Pay very close attention to the socket pin out numbers cast into the base plastic.