Frete Grátis em todos os produtos
- 【304 Stainless Steel】Our upgraded parking brake cable clip retainer is made of high quality 304 stainless steel, which has good wear resistance and corrosion resistance. Compared with the original factory plastic part, stainless steel is more durable and will not break.
- 【Effortless Installation】 Compared with the original part, the installation of this clip is very simple and fast. No need to dismantle too many parts, this upgraded clip can be directly installed on top of the original one,which will save you a lot of time and effort.
- 【Replace Part Number】This parking brake cable clamp holder replaces 34406854898, 6854898.
- 【Fit for】For 1 Series F20 07/2010-02/2015;For 1 Series F20 LCI 05/2014-06/2019;For 1 Series F21 07/2010-02/2015;For 1 Series F21 LCI 05/2014-06/2019;For 2 Series F22 10/2012-06/2017;For 2 Series F22 LCI 09/2016-12/2019;For 2 Series F23 03/2014-06/2017;For 2 Series F23 LCI 09/2016-12/2019;For 2 Series F87 M2 11/2014-06/2017For 2 Series F87 M2 LCI 09/2016-12/2019;For 3 Series F30 02/2011-07/2015;For 3 Series F30 LCI 09/2014-10/2018;For 3 Series F31 07/2011-07/2015;For 3 Series F31 LCI 09/2014-06/2019;For 3 Series F34 GT 07/2012-06/2016;For 3 Series F34 GT LCI 09/2015-12/2019;For 3 Series F80 M3 04/2012-06/2015;For 3 Series F80 M3 LCI 01/2015-10/2018;
- 【Fit for】For 4 Series F32 11/2012-02/2017;For 4 Series F32 LCI 05/2016-12/2019;For 4 Series F33 03/2013-02/2017;For 4 Series F33 LCI 05/2016-12/2019;For 4 Series F36 Gran Coupé 07/2013-03/2017;For 4 Series F36 Gran Coupé LCI 05/2016-12/2019;For 4 Series F82 M4 02/2013-02/2017;For 4 Series F82 M4 LCI 05/2016-12/2019;For 4 Series F83 M4 06/2013-02/2017;For 4 Series F83 M4 LCI 05/2016-12/2019.
- 【Package Included】1 × Parking Brake Cable Clip Retainer, 2 × Rubber Tubes, 1 × Manual.
Replacement Rear Parking Brake Cable Left Driver or Right Passenger for Chevy GMC C10 K10 K5 Blazer Jimmy Suburban
*$537.50
14AWG SAE to Car Cigarette Lighter 12V Cigarette Lighter Male Plug to SAE Connector Extension Cable with SAE Polarity Reverse Adapter(5FT)
*$274.00
Frete Grátis em todo o BrasilProduto Original Importado dos EUA
Upgraded Stainless Steel Parking Brake Cable Clip Retainer with Rubber Tubes Compatible with BMW 1 Series F20/F21, 2 Series F22/F23, 3 Series F30/F31, 4 Series F32/F33/F36…
*$361.00
Informação adicional
| Manufacturer | EVRBUL |
|---|---|
| Brand | EVRBUL |
| Model | Upgraded Stainless Steel Parking Brake Cable Clip Retainer with 2Pcs Rubber Tubes |
| Item Weight | 1.44 ounces |
| Package Dimensions | 3.94 x 3.43 x 0.94 inches |
| Country of Origin | China |
| Item model number | EV34406854898 |
| Exterior | No |
| Manufacturer Part Number | EV34406854898 |
| Date First Available | June 4, 2024 |
Bryan –
Works as expected fast shopping got rid of the grinding noise of my driveshaft rubbing the emergency brake lines
Hollaback –
This product is a must have if you’re replacing your parking brake cable retainer clip. Easier to install than OEM. Less expensive than OEM. And won’t break like the OEM model. 2 thumbs up !
A Car Guy –
The dealer wanted over $1,000 to install a plastic replacement part. The process took me a couple of hours since a brace and heat shield needed to be removed but the installation went smoothly.
Heather Fisher –
Car no longer makes the terrible noise. ’17 340i. From husband “Not easy to install but part does what it claims. Ratcheting 13mm wrench is highly recommended. This may only apply to a dual exhaust car, don’t know how the single exhaust looks. If you’re working under the car on jackstands, remove crossmember and the nuts holding the heat shield, disengage it from the studs and slide heat shield forward and rotate it to give yourself as good of access as possible. Loosen left side exhaust hangar at rear but don’t remove the nut and then remove right side exhaust nut. This allows some extra clearance. Pull the parking brake cables out of the clips on the control arms and I used cable ties to pull the PB cables roughly where I wanted them to be. At that point you’re working blind to line up the new bracket with the stud, holding the rubber tubes in place and starting the nut. As others have mentioned, the stock washered nut is not going to work but the exhaust hangar nut is a perfect example of what you need to replace it.”
Jko –
Much cheaper alternative but just as effective as the $100+ one. Was a PITA to install but it fixed the problem. No more noises even when WOT.
Cassy Stringfield –
I don’t typically write reviews, but this product was much more than I could have ever anticipated. I drive a 2015 BMW 320i as my daily commuter car. The “scratching” noise when turning corners and accellerating drove me nuts! After researching and narrowing the issue down to a CHEAP plastic part I was about to buy the expensive aftermarket brand for $150 to $200. Then i found this and thought id give it a try. Man was i excited after install! First, it arrived as expected and packaging was defitely acceptable. The ease of installation was much better than I thought. After jacking and safely supporting the car, it was installed in only 35 minutes. I was able to lower the exaust, remove the cross member and lower the heat shield with only a dozen or so fasteners. Then i removed the 13mm nut with a ratheting wrench and installed the rubber cable protecters and new clip over the broken one in no time. Every thing done safely and securely in 35 minutes! I took the car for a test drive and my smile came back! This clip is heavy duty and took away all the headaches from the issue. No more scratching noise! GREAT product, seller, and results! This customer is more than satisfied. Im ecstatic!!! Thank you!
RICk
S. Ernst –
Worked as stated on my 428i. The hardest part of the install is limited space to work, but is less than the $1000 that BMW charges to drop the fuel tank.
Victor –
Bracket does exactly what it was built for and easy to install. Only complaint, the wings could be a little shorter for easier install without the need to clip or break off the damaged clamps from the original plastic bracket. It isn’t necessary the remove the braces, to lower the exhaust, or remove the heat shield since there is enough space to get this bracket in-place and tighten down. A 13mm ratcheting wrench and a 10mm socket will work perfectly fine. Job took 30 minutes with raising and lowering the car. P.S. I didn’t use the rubber sleaves as a personal preference and much easier to install without. Everything is super tight so no need.
Miguel Ángel Ramírez Gómez –
Cuando aceleraba, dentro de la cabina se escuchaba un chirrido, como si algo rosara (transmisión o suspensión) investigué hasta que dí con esta pieza que no solo fué la que me salvó, quedé completamente satisfecho ya que es algo que uno mismo puede hacer.
Simplemente contento con mi compra y agradecido de que solucionó mi problema.
Adjunto una foto de la pieza original y el peoblema que ocasionaba. (El cable del freno de mano se salió de su posición.)