Frete Grátis em todos os produtos
- 90 degree bend
- Connects 3 inch diameter intake tubes to 3 inch diameter or 2-1/2 inch diameter components
- Great option where space is limited and an immediate bend will allow use of an intake system
- Lifetime warranty
Walker 31854 Exhaust Flange
*$289.00
Dorman 598-114 Exhaust Gas Recirculation (EGR) Line Compatible with Select Ford Models
*$827.20
Frete Grátis em todo o BrasilProduto Original Importado dos EUA
Spectre Performance 8791 3″ ID 90 Degree Boot
*$445.00
Informação adicional
| Manufacturer | Spectre |
|---|---|
| Brand | Spectre |
| Model | 8791 |
| Item Weight | 12.3 ounces |
| Product Dimensions | 5.1 x 3.6 x 6.5 inches |
| Country of Origin | China |
| Item model number | SPE-8791 |
| Is Discontinued By Manufacturer | No |
| Exterior | Machined |
| Manufacturer Part Number | 8791 |
| OEM Part Number | 8791 |
| Date First Available | November 3, 2010 |
BML –
All three of these intake components are from Spectre performance. They worked great for my custom intake (Subaru EJ22 in 67’VW bus) setup. Very happy with these products!
RKingsroom –
Item accurate as described, material is very sturdy, excellent low profile for my build.
Amazon Customer –
Needed a rubber elbow, received a rubber elbow, went on without a hitch, does what it’s suppose to.
denae –
It works
It works
Amazon Customer –
Great product, works great, really good material.
Amazon Customer –
Great product and low profile. I used it to make a custom snorkel for my 99′ TJ Wrangler. They fit under the cowl and don’t mess with my wipers.
philip middleton –
Great build quality, very durable & perfect fit for 3″ pipe. Just bought 2021 Polaris Sportsman 570 Trail ATV & for whatever reason, the clutch exhaust outlet is much shorter on the premium models. Duct exits right in front & above rear tire, perfect position for mud/water to splash into causing belt to get wet & slip. Used these elbows along with 3″ PVC pipe to extend duct right behind rear plastic at rear bumper. Finished off with the Spectre blue air filter to keep mice & other debris out. Works great & looks like custom air intake!
RKingsroom –
I needed to change the the air flow unit on my 99 Jeep WJ, inline 6 and this worked fine along with small modifications. I went to Home Depot and purchased duct adapter and wrapped it with reflexive tape and drilled a hole for the vent tube.
philip middleton –
DO NOT BUY!!! I bought two for my GTR and within the first 250 miles after my build one has already cracked/torn. (Have not even built more than 5 psi on base map tuning.) You have been warned…
MOOREFIRE –
The product seems sturdy enough. Based on reviews here, I poked and prodded at it to kake sure it wasn’t going to tear in use. Its fine.
It comes with two hose clamps, but I didn’t use them. Its for my unpressurized intake, and it fits tight enough not to pop up.
I used it with a Spectre bulkhead fitting, and a Spectre flex hose. It fit the bulkead fitting fine. But how to attach it to the hose? The little 2.5″ adapter thing that comes with it was too flimsy and too short.
So I went to Home Depot and got a 3″ dryer duct pipe, about a foot long for under $4. Cut it down to about 4″ long, painted it black for good measure, and it works perfectly. Slightly tight fit for both the hose and the 90. Had to wrestpe them both on. But they sure won’t come loose.
Don’t use flat paint, will just make it that much harder to slide hose on.
One advantage of using the metal dryer duct is its so thin, it won’t impede flow.