Frete Grátis em todos os produtos
- PERFECT FIT – This high quality SPST (Single Pole Single Throw) ON-OFF push switch is manufactured to fit in the OEM space available in your Toyota car. Gives your vehicle upgraded with this factory look switch
- SUPREME QUALITY – Laser etched directly onto the push switch face using modern high tech laser engraving equipment to ensure long image life. Features a backlit panel that illuminating when the switch is turned on. There are 2 LEDs inside the switch: UPPER Symbol/ LOWER Letters. Easy for you to know the working status
- STURDY DURABILITY – The push button switch is made out of heavy duty ABS plastic and come in a mate black surface color. The surface size is 1.28″ x 0.87″. It has short circuit protection to protect your vehicles, ensure years of service. Safe and long lasting
- EASY INSTALL – Rated at 3Amp 12V, comes with connector wire kit, easy to install. It is simple to connect the switch: The Green wire goes to the battery, the red w/yellow stripe closest to green wire goes out to the relay; the black wire connects to the ground, while the red w/yellow stripe closest to black goes to the dash
- WIDE APPLICATION – This model push switch compatible with Toyota Sequoia 2008-ON, Toyota Highlander 2008-ON, Toyota Tacoma 2012-ON Center ONLY, Toyota Tundra 2008-ON, Toyota 4Runner 2010-ON, Toyota RAV4 2008-2012, Toyota Yaris 2008
2PCS AZ973-1C-12DC4 Power Trim Tilt Relay, Replacement for Mercury Outboard Motor, Replace 88275182751A1, 83854138, 73040, 828151
*$328.00
for Tyco VF28-35F14-Z05 40A 12193601 Automotive Relay 5 Pins
*$372.20
Frete Grátis em todo o BrasilProduto Original Importado dos EUA
Push Button Switch 12V with Wiring Kit – Blue LED Light BAR Symbol, Compatible with Toyota Sequoia Highlander Tacoma Tundra 4Runner (Surface Size 1.28 x 0.87 inches)
*$265.00
Informação adicional
| Operation Mode | ON-OFF |
|---|---|
| Current Rating | 3 Amps |
| Operating Voltage | 12 Volts (DC) |
| Contact Type | Normally Open |
| Connector Type | Button |
| Brand | MNJ Motor |
| Terminal | Button |
| Circuit Type | 1-way |
| Mounting Type | Pole |
| Actuator Type | Push Button |
| Switch Type Push Button | Switch Type Push Button |
Amazon Customer –
Love this product. Used for Hood mounted LED light bar
Jordan L. –
Installed this in my 2013 Toyota Tacoma to control my Baja Design S8 light bar. Works and looks perfect in the factory switch slot. Highly recommend.
Amazon Customer –
I read the other reviews that talked bout how these switches are unreliable. I should of heeded that advice. These switches are un mitigated junk. switch does not stay on consistently even though the button does latch.
Amazon Customer –
The fit and finish of the switch is very good. I haven’t had to use it much yet, so we will see how it it holds up over time. The wiring diagram was not in the box or not helpful. I looked up online and found one that worked. I didn’t wire it to accessories, but may in the future. In other words if someone is not paying attention and left it on it would run down the battery. As of now I would order from this company again.
Jordan Bannister –
I ordered two of these for a 2013 Toyota 4Runner SR5. The switches are great quality and seem to be well manufactured. The wireing is nice and long. I installed one today on my front bar, behind the grill. The issue that I had was the Switch has 4 wires and the harness has 3. After some deep diving on the internet I found the way that the switch needs to be wired up. I put the switch in the dash port and it would not stay on. I pushed the switch, gently, on all surfaces of the switch when it is in the dash and it turns on then off. I slide the switch out of the dash and it works as it should. Am I missing something here? Is there supposed to be a spacer behind the switch? I am going to try the other switch that I ordered and see if that one does the same thing. I may just have a bad switch. I will update later.
UPDATE:
I was able to add some electrical tape (3 pieces) to each SIDE of the switch to act as a spacer on the sides, this makes the switch functional for what I need. The best part is, now that it is starting to wear out, I can add another piece to either one or both sides and it will still work.
R.Hector Campos –
I bought one for my FJ last year and I had zero issues.
Bought one for my Tacoma and when installing it the 4 wire plug wouldn’t come unplugged easy at all once it was plugged into the switch.
When wiring it up the main red wire came out of the pin. It was a real pain to get out and to re crimp and change out.
But once everything was re installed and heat shrunk good to go.
Not sure if there is anything else I could have bought, but it does the job.
Jordan L. –
The switch fit perfectly where it should and the wiring was correct in my 21 4Runner. 3 stars as the switch itself was a little sticky at first and I had to trim the back of the switch where the factory notches are in order for the switch to push far enough in to turn on and off. But with a little know how and trimming, it works great now.
Looks fantastic like Toyota had put it there for me!
David S. Zahler –
Works great. The light from the switch is just right.
Raul Velasquez –
Perfect fit for my 2016 Toyota 4Runner SR5. Easy to install. Light bar wiring may vary, so the wiring harness colors might not match perfectly. You’ll need to figure it out but there are several videos on YouTube that can assist. Solid product and way cheaper than competitors!
R.Hector Campos –
works as intended