Frete Grátis em todos os produtos
- PROBLEM SOLVER GUSHER BEARING — Metal-to-metal design provides strength and allows grease to flow through bearing surface for reduced friction and long life
- STRONG AND DURABLE — Ball studs are heat processed to match or exceed OE requirements to inhibit premature failure and improve fatigue strength
- GREASEABLE SOCKET — Inhibits corrosion and wear by allowing new lubricant to flush debris
- KEEPS DIRT AND WATER OUT — Pre-installed boot shield socket components from wear-causing debris
- ABSORBS IMPACT — Belleville preload washer helps keep the bearing package tight as bearings wear
- EASY TO INSTALL — Precision tolerances for easy installation and steering alignment giving you a perfect fit right out of the box
- COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
10MM Ball Stud Widen Mounting Brackets for Universal Gas Struts Lift Supports Shocks Spring Prop 4PCS, Silver(Bigger Version)
*$343.00
For Grand (Set of 4 Front Rear) ANGLEWIDE Shocks Absorbers Struts Set Fits 1999 2000 2001 2002 2003 2004 for Jeep for Grand Cherokee 4.0L / 4.7L Amortiguadores - 344342 344341
*$1,140.10
Frete Grátis em todo o BrasilProduto Original Importado dos EUA
MOOG K6541 Front Lower Suspension Ball Joint for Chevrolet Silverado 1500
*$525.10
Informação adicional
| Manufacturer | MOOG |
|---|---|
| Brand | MOOG |
| Model | BALL JOINT |
| Item Weight | 1.43 pounds |
| Country of Origin | USA |
| Item model number | K6541 |
| Is Discontinued By Manufacturer | No |
| Manufacturer Part Number | K6541 |
| OEM Part Number | K6541 |
| Date First Available | November 10, 2005 |
Dmitri Reali –
Installed in September 2022. So far they work, unlike the upper ball joints installed at the same time.
Joe Reyna –
I love the low-profile boot compared to the OE GM ones where you have to remove before installation.
Tim Jackson –
Installed the Moog K6541 into my 2016 GMC Sierra 1500 Denali, which has the cast iron control arms. These fit well and seem to be built strong. Replaced my worn out stock ball joints with 155kms on them. They are genuine MOOG and are greaseable. Using a ball joint press tool made the install very easy. I did both sides in 2 hours. Torqued to 37ft/lbs +130* as per oem spec.
Tim Jackson –
This Lower ball joint fits 2002 GMC Sierra 1500 with 4×4, Good quality and really stiffens up front end. Moog is one of the best when it comes to suspension parts no doubt!
Great product real lather feels great in my hands…. and durable –
Works great
Conrad –
Good replacement for oem. Grease fitting included.
bigboyjon –
Good fit and look well made. i used on a 1999 silverado and the project turned out well.
Rc –
Thanks
Aaron –
Perfect fit on a 2007 Silverado 1500 2WD. The OEM ones are a pain to remove, but these insert very easily with a ball joint press. The fact that these are serviceable mean that they should last a very long time (unlike the OEM). They are built very sturdy. My one complaint was that AFTER the installation was finished and everything was put back together, while filling with grease, one of the ball joint dust boots had a hole in the side, so as it began to fill with grease it just squirted out the side from a location that would not likely have been damaged during installation (the dust boot is retracted inside the steel housing until you fill it with grease). I contacted Amazon and they are sending a replacement. I would recommend doing some kind of inspection before you install to prevent completing the job only to find out that one is defective.
Robert Walters –
I bought these for my 2010 Silverado. I’m sure the product is great and fine quality however while it says it fits it…come to find out for my year, make, and model there is no pressing the old ones out as they come factory pressed into the upper control arm. I’ll give it 5 stars though because they are high quality and customer service and shipping were top notch and the return was accepted with no issues.