Frete Grátis em todos os produtos
- 【Fuel Sender Material】: Fuel sending unit is made with heavy duty stainless steel. This water level sensor is reed switch, durability and reliability, steady output signal. No adjustment needed for tank.
- 【Perfect Replacement Fuel Sender 】: Sucicago Reed Switch Diesel Fuel Water Level Sensor is a Better Option Than the Traditional Lever Type Sensors. The Boat Fuel Tank Will not Effected by The Constant Movement Caused by Waves and Boat Rocking.
- 【High Quality Material】:SAE 5 hole mounting pattern, heavy duty 316 stainless steel and rugged construction.Signal Output: 240-33 ohms.Wide Application: It Could Support Fuel Level Gauge and Water Level Gauge for Boat/Auto.
- 【Note】: to allow the sender not hit the bottom of the tank, the length of sender should be 1″ less than the depth of the tank if tank is plastic, and 0.5″ less than the depth of the tank if tank is metal .
- Your satisfaction is our great motivation, if you have any questions before purchase or after purchase, please feel free to contact us, we will give you a satisfied solution within 24 hours.
3PCS Auto Water Temp Joint Pipe, Aluminum Sensor Gauge Radiator Hose Adapter, Universal Water Temperature Extension Adapter with Clamps (32MM)
*$243.50
1x Harness Connector for O2 Oxygen Sensor Mazda Subaru 10"
*$397.00
Frete Grátis em todo o BrasilProduto Original Importado dos EUA
Fuel Sending Unit and Gauge Kit Boat Fuel Sender Fuel Water Level Sensor 240-33ohms 7″ (175mm) Fuel Tank Sender Stainless Steel Gas Sensor for Boat Car Truck Vehicle
*$517.00
Informação adicional
| Operation Mode | OFF-NONE-ON |
|---|---|
| Current Rating | 0.3 Amps |
| Operating Voltage | 12 Volts |
| Contact Type | Normally Open |
| Connector Type | Solder |
| Brand | ZHSYMX |
| Terminal | Through Hole |
| Item dimensions L x W x H | 4 x 8 x 4 inches |
| Actuator Type | Reed Switch |
| Contact Material | Stainless Steel |
| Switch Type Bipolar Transistor | Switch Type Bipolar Transistor |
| Mounting Type Through Hole Mount | Mounting Type Through Hole Mount |
Marc Garman –
Simple instzllation. Very bright. Seems to work just fine.
ERL –
+++++ These are the greatest fuel senders AND NO HASSLE INSTALLATION and it works great in my 1919 T-Bucket Roadster’S CUSTOM GAS TANK. Thank you. 5 STAR, A+ ALL THE WAY. +++++
Bill C –
Works well, but for the measurement range they give of the tank it works in, the level is off, I, ordered this up to one inch shorter than the tank dept as they instructed but when the tank is 1/2 full it reads less than 1/4 tank, seems way off, had to make up an additional float to make the sensor ride higher to compensate.
jason mowery –
Black wire ground, orange wire ignition+, yellow wire sender wire from tank! I didn’t get directions with my guage. Hope this helps. Guage is working great so far.
Julie –
Purchased for my RV and the original one (had the arm that had to be trimmed) seemed impossible to get to read correctly. My tank is 6″ deep and it fits fine, have not filled the tank all the way up but it is reading 1/4 which is probably about right from my math. It does to come with a seal you will have to use the old one or make one. It also did not come with bolts.
DisneyCouple –
Works great. Hole pattern lined up exactly. It does come with screws but they were not the right thread as I needed so I just used my old ones. Used to replace sending unit in bass boat fuel tank.
Amazon Customer –
Thing never worked upon installation. Lost twice as much as this POS cost in time/labor.
M$ –
Worked great easy install