Frete Grátis em todos os produtos
- Easy repair, saves money
- Can be installed without removing axle from the vehicle
- For cars with large shaft
- Comes with clamps and grease
Beck/Arnley 104-1764 Transmission Mount
*
MDEOOSKY Transmission 3-Bolt Adapter Flange Yoke Kit, Replacement for GM 6L80 6L90 8L90 10L80 10L90 TR6060 TR3160, Replacement for Pontiac GTO
*$1,321.00
Frete Grátis em todo o BrasilProduto Original Importado dos EUA
FB3002 Large Shaft Universal Replacement CV Boot for Toyota style CV Joints.
*$445.00
Informação adicional
| Manufacturer | Astoria 2000 |
|---|---|
| Brand | FLEXX BOOT |
| Model | FB3002 |
| Item Weight | 10.2 ounces |
| Package Dimensions | 5.1 x 4.4 x 3.6 inches |
| Country of Origin | Taiwan |
| Item model number | FB3002 |
| Is Discontinued By Manufacturer | No |
| Manufacturer Part Number | FB3002 |
| Voltage | 12 Volts |
| Date First Available | March 28, 2013 |
Warren Tolson New Zealand –
This universal boot was flexible enough that it worked well with a plastic cone tool to flex over it with some effort and install to repair an outer boot without removing the axle. The clamps that came with the boot worked well. You do need a special tool to crimp the clamps. I used this boot to replace an outer boot on a rear axle for a 2007 Joyner 650 dune side by side. Will certainly by more if needed.
Eric M. –
The CV Boot Fit snuggly as it had lots of stretch to accommodate the cv shaft.
There was no need to replace a good OEM axle because of a torn boot. It is a very inexpensive fit.
Some cv boots are very stiff but this one is flexible and looks like it will hold up for a long time.
The clamps were terrific as well.
Thanks for the quality product
Eric M. –
Used to keep ice from getting into the thrust bearing on my antenna tower.
Nathan Casteel –
They WILL stretch over but my GAWD it’s not as easy as the videos shows. Best bet is use a towel and lots of lube
knapb –
I’ve used these Astoria Flexx Boots for years. I am satisfied with the durability and performance. Must use the correct size boot, cv boot clamp pliers, and installation tool. With that said check the contents of the box before starting installation. One of the box was missing the packet of grease. I wish Astoria had a part catalog for vehicles older than 1998.
Tina S –
This boot was to be used on an outer cv joint. The boot is made of neoprene I believe. It was very flexible. I was going to use it on a 2011 Toyota 4runner 4wd. The dimensions were too short all around. I measured cv opening 92mm diameter, cv axle shaft opening 23 mm diameter, length was 4.25 inches. Now the boot is made to stretch, though I did not want to take the risk. 2011 Toyota measurements were cv opening 102.5mm diameter, cv axle diameter 29.8mm, length 120.65mm. I did not try to put it on since I would have to destroy the installed boot.
spend thrift –
Bit hard to start with and keeping gloves grease free was difficult but worked well
Nathan Casteel –
Fits vintage audi shafts and was actually able to stretch over with the air tool where normal stretch boots couldn’t
lrrp101et –
This is a great boot. The rubber was incredibly elastic allowing me to work it over the joint without removing the whole axle or buying a special tool.
TIP: if you really work it, you can first turn the boot inside out then roll it over the outer joint with a pair of flathead screwdrivers. The boot was that elastic!
I appreciate that clamps and grease came with it but unfortunately my large clamp must have snapped and fell off on the road with a couple weeks of driving. Otherwise this would be a 5-star for me.