Frete Grátis em todos os produtos
### Descrição do Produto
O DEWHEL 12V 0.02A-10A 2-Pin CF-12 Automatic Electronic LED Flasher Relay é a solução ideal para quem busca um desempenho confiável e eficiente em sinalizações de motocicletas e scooters. Este relé eletrônico de pisca-pisca é projetado para eliminar o problema comum de hiper piscar, que ocorre frequentemente ao substituir lâmpadas incandescentes por LEDs. Com sua configuração de 2 pinos CF12, este relé é compatível com uma ampla gama de veículos, garantindo que os sinais de mudança de direção pisquem em uma taxa normal, independentemente do tipo de lâmpada utilizada.
Com uma corrente de comutação que varia de 0.02A a 10A, o DEWHEL é robusto o suficiente para atender às necessidades de diferentes sistemas elétricos. Seu design cúbico compacto (dimensões: 1.43 x 1.33 x 1.00 polegadas) facilita a instalação em espaços reduzidos, tornando-o uma escolha prática para motocicletas e carros. Este relé não apenas corrige o problema de pisca-pisca rápido, mas também previne falhas de sinalização, como o piscar fraco ou a ausência de pisca-pisca em LEDs.
### Instruções de Uso:
Para instalar o DEWHEL 12V 2-Pin CF-12 LED Flasher Relay, siga os passos abaixo:
1. Desconecte a Bateria: Antes de iniciar a instalação, desconecte a bateria do veículo para evitar curtos-circuitos.
2. Localize o Relé Original: Encontre o relé de pisca-pisca existente no seu veículo. Ele geralmente está localizado na caixa de fusíveis ou próximo ao painel de controle.
3. Remova o Relé Antigo: Desconecte o relé antigo, tomando cuidado para não danificar os conectores.
4. Conecte o Novo Relé: Insira o DEWHEL 2-Pin CF-12 no lugar do relé antigo, garantindo que os pinos estejam bem encaixados.
5. Reconecte a Bateria: Após a instalação, reconecte a bateria e teste os sinais de mudança de direção para garantir que estão funcionando corretamente.
### Características do Produto
– Tipo: Relé Flasher Eletrônico 2-Pin CF-12
– Tensão: 12V
– Corrente de Comutação: 0.02A – 10A
– Dimensões: 1.43 x 1.33 x 1.00 polegadas
– Compatibilidade: Ideal para motocicletas e scooters, além de carros
– Função: Elimina a necessidade de resistores de carga, garantindo um piscar normal com lâmpadas LED ou incandescentes
– Design: Forma cúbica compacta, facilitando a instalação em espaços limitados
### Perguntas Frequentes (FAQ)
Pergunta: O DEWHEL 12V CF-12 é compatível com todos os tipos de lâmpadas?
Resposta: Sim, o relé é projetado para funcionar com lâmpadas LED e incandescentes, garantindo um piscar normal em ambos os casos.
Pergunta: É necessário usar resistores de carga com este relé?
Resposta: Não, o DEWHEL elimina a necessidade de resistores de carga, permitindo que os sinais de mudança de direção funcionem corretamente sem eles.
Pergunta: Posso instalar o relé eu mesmo?
Resposta: Sim, a instalação é simples e pode ser feita por qualquer pessoa com conhecimentos básicos de elétrica, seguindo as instruções fornecidas.
Pergunta: O que fazer se o pisca-pisca ainda estiver rápido após a instalação?
Resposta: Verifique se o relé está corretamente conectado e se não há problemas elétricos no sistema. Se o problema persistir, consulte um profissional.
Pergunta: Este relé é resistente a intempéries?
Resposta: O DEWHEL é projetado para uso em veículos, mas recomenda-se evitar exposição excessiva à água e umidade para garantir sua durabilidade.
Wildcat –
Excellent
Shaun –
Worked for the hazards on my 93 chevy k1500 z71. its a little weird because its silent, but it does work for my hazards with all LEDs.
waymon d. –
When I first installed it the flasher wouldn’t work. If it doesn’t work you will need to reverse the wires.. couple butt connectors and 6 in wire will fix it
Ray Pohl –
Completely satisfied.
Vanessa –
I am wiring my own turn signals and this flasher works with LED’s. I tried 3 others and they either would not work or would shut off if a load was applied to the battery. This flasher works.
Thomas Eagling –
I used this on my 2020 Grom SF after installing LED directionals and taillights. It worked well to prevent hyper flash and is still working a year later. Would recommend.
Customer –
This is the second LED flasher I’ve tried sold on amazon. I’m 0 for 2.
My results are, a blinker will make the hazards come on, rather than just a blinker. The first relay I tried it was a coin flip as to which I’d get, a blinker or a hazard light flash. With this one, I’m always getting a hazard the first time, then the blinkers for the next times thereafter. After about 10 mins or a battery disconnect/reconnect test, it’s back to hazards only the first time.
If I just put my test light on these flashers, that’s enough load to make them work correctly 100% of the time. These just can’t sense the light load of all LED lights. I think I’m giving up and just going to install some load resistors and then either of the LED flashers will always work 100% of the time.
Just leaving incandescent bulbs in the front blinkers, I never had a problem either, it’s when I went full LED the problem arose.
I’m sure someone, somewhere, makes a sensitive enough LED flasher, but because every car is different, our loads are all going to be different. If it worked for someone, it should work for me though as I’ve got a ;68 t-bird with multi blinkers in the rear and it’s still not enough load for this flasher to sense.
I know if I just install a couple load resistors I wont have to worry anymore. I’m not convinced any of these are going to be sensitive enough, but with just adding a bit of load, it’s going to be a non issue. I should have just gone that route, rather than trying another one of these. It is a bit better than the first one I tried. I mean I could turn and and off my blinkers twice, whenever I wanted to make a turn, knowing the first time will be hazard lights, then the next a blinker but since I know load resistors will fix it and not have things wonky, I’ll do that.
Too bad these didn’t just work though.
Update:
I decided to just add small incandescent lights (little trailer lights I had kicking around) in the trunk, to place a light load for this flasher to sense. 100% working blinker and hazard light now.
I opted for this route, due to research saying load resistors got hot. Didn’t want to risk that, so just added small lights inside the trunk. I even mounted them so that I can see if they light up, once a year when I bring the car out, whenever I put the blinkers on. If the bulbs are good, so will be my blinkers and hazards. Will probably take 10 years or more to blow a bulb, plus it cost me nothing.
Since I went this route, I didn’t need to bother with this second LED flasher, my first one works in the same manner….. so long as there’s an incandescent bulb for each blinker, it’s all it takes. Inside the trunk, no one can see it on (it only comes on when I use a blinker) and nothing to worry about heating up causing a fire.
This LED flasher still failed, however. It was supposed to sense the LED lights and those alone were supposed to be enough load for it, so as to avoid this trick. Oh well. Maybe years latter when these improve, I’ll try another so I can remove my lights. Until then, I’ve got a safe car with all lights working at least.
Atsushi Matsubara –
This flasher relay works with LED bulbs. But on my (but maybe not on others’) 69 mustang the wires needed to be crossed for it to work. I guess, in the original flasher relay, bi-metal switch inside works regardless of which way the current may run. However, in this flasher relay, the IC inside used to detect the lower current through LED bulbs does not work properly if the load and hot wires are not connected properly. Since the 69 Mustang comes with an L-shaped connector that fits on the flasher relay only in one way, I assumed that the load and hot wires will connect correctly to the relay. My guess is that the LED flashers that I purchased previously and did not work would have worked, if I had crossed the wires too. I wonder also if some old cars with L-shaped connectors have the wire arrangement that works with these LED flasher relays without crossing the wires. In any case, if it does not work, I would suggest crossing the wires.
Shakadula –
1.22.2025. I bought the two brake light led’s to replace my 1157 bulbs in my classic 67 Buick. Didn’t work so got onto YouTube only to find out I needed an additional part. Found this unit and it was a plug and play install and now I have brake lights, tail lights, emergency flashers and my front parking original non-led lights still work.
Product works as described. How long it will last………..time will tell.
Guillermo Tovar –
El producto llegó bien cerrada y a tiempo. Al instalarlo, law luces no encendian. Verifiqué las conexiones de acuerdo al diagrama y todo estaba bien, pero seguir sin funcionar… se que el producto es bueno, y realizaré una nueva compra, pero creo que me tocó la mala suerte de ser el porcebtaje de error